System operation matters needing attention

(1) please by all means must carefully read through the user's manual and the preserve well prepares the consult.
(2) to prevent the fire or avoid the thunder stroke, please do not expose this system's equipment in the rain or places the moist place.
(3) when installment, debugging and maintenance, please do not want the charged operation.
(4) please pay attention all attentions which and the warning item this showing mentions.
(5) please frequently inspect in alarm apparatus' SIM card to be whether rich, in order to avoid the SIM money owed causes the system to be unable to report to the police. One of inspection ways dials the handset card number, if has the question, will have the corresponding voice prompt.

First, before installing, is sure to remember the following item:

before * installment, please by all means must careful reading this explanation
* in the installation process not to be possible the charged operation

after * the installment finished, must inspect the connection line repeatedly, confirmed after unmistakable, could electrify
* because if the installment fault creates the equipment trouble, Our company cannot be responsible

Second, alarm apparatus end connection

(1) binding clamp schematic drawing
Explained: For the convenience understanding, following digit marking, is in turn from left to right:

Switch quantity

The DI1 road is the water immersion detector, connects on 1,2 binding clamps, already continually good.

Simulation quantity

AI1: The post 17 are the humiture sensor 1 temperature lead wire.
AI2: The post 18 are the humiture sensor 1 humidity lead wire.
AI3: The post 19 are the humiture sensor 2 temperature lead wires.
AI4: The post 20 are the humiture sensor 2 humidity lead wires.

The humiture sensor connection, the alarm apparatus meet the oral plate end:

Short note disposition order

Attention:
In below all short note order's punctuation mark is the half-angle, namely under English condition.
After all instruction success, the system can return to the confirmation information.

1. the system super manager number disposition registers

Registering: Old number: 88888888888; Old password: 88888888; New number: 13701241111; New password: 88888888
Note: 1st, only then the super manager only then may dispose the equipment attribute as well as the ordinary manager;
2nd, only then the super manager only then may transmit “the replacement” the order; (already lets the entire equipment reply original state)
3rd, if wants the super management also to accept the warning function, needs to dispose it the ordinary manager;

2. the ordinary manager number disposition instruction (completes by super manager)

Number disposition: Number one: 137012455 **; Number two: 137012455 **; Number three: 137012455 **; Number four: 137012455 **
four: 137012455 **
Note:
1st, most may dispose 5 ordinary managers, but an information can only receive 70 characters, therefore 5th must edit;
2nd, the ordinary manager may accept time the unit exception the warning, and may immediate “the inquiry” the device status;

3. the humiture sensor disposition order (super manager completes)

Simulation quantity disposition: Serial number: 1; Name: Temperature 1; Upper limit: 30; Lower limit: 00; Linear ratio: 0.0122; Demarcation datum: 0; Time delay: 5;
Simulation quantity disposition: Serial number: 2; Name: Humidity 1; Upper limit: 70; Lower limit: 00; Linear ratio: 0.0244; Demarcation datum: 0; Time delay: 5;
Simulation quantity disposition: Serial number: 3; Name: Temperature 2; Upper limit: 30; Lower limit: 00; Linear ratio: 0.0122; Demarcation datum: 0; Time delay: 5;
Simulation quantity disposition: Serial number: 4; Name: Humidity 2; Upper limit: 70; Lower limit: 00; Linear ratio: 0.0244; Demarcation datum: 0; Time delay: 5;
Note:
1st, in the order serial number and the linear ratio are invariable, other may change;
2nd, the temperature serial number is 1, 3/humidity serial number is 2, 4, linear ratio along with it correspondence;

4. the water immersion sensor disposition order (super manager completes)

Switch quantity input: Serial number: 1; Name: Water immersion condition; Warning condition: Pass; Warning content: Water leakage; Time delay: 5
Switch quantity input: Serial number: 1; Name: City electricity condition; Warning condition: Opening; Warning content: Power failure; Time delay: 0